Geeetech 3D Printer Motherboard for DIY Pro B Pro C Pro W Prusa 3D Printer

Description: GT2560 is a compact board that is integrated with the mighty function of the Arduino Mega2560+Ultimaker. The GT2560 can not only take full place the Arduino Mega2560+Ultimaker on respect of both software and hardware, but has more premium features: the streamlined interfaces effectively avoid the unnecessary troubles, well-regulated compaction of components highly integrated saves more space and easier to be mounted on most applications. 5 stepper motors, swappable driving modules, mighty ATmega2560 processor with 256k memory, 16MHz operating frequency, high-performance USB serial converter FT232RQ, all these make the GT2560 an ideal option for a 3D printer control board. What’s more, GT2560 can run over 12V and output 90W to a MOSFET, which gives higher torque and higher rotation rate. Features： 1.Integrated with the mighty function of the Arduino Mega2560+Ultimaker, The GT2560 can not only take full place the Arduino Mega2560+Ultimaker on respect of both software and hardware, but also features compact size, more convenient connection, and more stable. 2. Adopt ATmega2560 as the main control chip, coupled with the high-performance USB serial converter FT232RQ. 3. The power pack: operating voltage is 12V-24V; double power supply design feeds for heatbed and logical part separately. The current is 12A for heatbed and 5A for other parts. The cooling fan can support 12V 4. The main circuit adopts SMD fuse tube, the diode added to the power port can provide reverse protection to the whole circuit, in addition, the 5V USB is USB port protected with 500mA Recoverable fuse. 5． 3 12v fan output and one PWM output for LED or other lighting equipment. 6. 3 55Amp MOSFET (with LED indicator, the actual output is restricted by the PCB board and the connector), all 3 MOSFET are equipped with heat sink to ensure sufficient heat dissipation and stable operation. 7. Support 5 A4988 stepper drivers (3 for X/Y/Z axis, and 2 for extruders); the subdivision of stepper motor can be setup by dial switch, eliminating jumper caps, easier to operate. 8. 3 temperature sensor input (100k thermistor is recommended) 9. Extended LCD and SD card interface support both LCD2004 and LCD 12864, with which you can print without your PC. 10. The firmware is the prevalent Marlin, which is known for stability, usability, and high-performance. GT2560 VS Ramps1.4+ mega 2560Compared with Ramps1.4+ mega 2560, GT2560 has the following merits： 1. Further compacted volume and space-saving. 2. Integrated peripherals ensure more stable connection. 3. Added heat sink provide better heat dissipation for MOSFET 4. Separate control for fan and extruder 5. Support LCD2004 and LCD12864 without using adapters Here is a detailed comparison between GT2560 and Ramps1.4+ mega 2560: 3D control boardGT2560Ramps1.4+mega 2560Main control chipATMEGA2560ATMEGA2560dimension110X80X25 110X60X40Extruders 22thermistor33Endstop 66Controllable fan 11(if you use dual extruders, this is not applicable)uncontrollable fan33Stepper motor driver 55Need Stack board NoYesLCD2004 and 12864Yes Yes(need adapter) Update log: A 3-pin straight pin is added to connect with 3D touch auto leveling sensor, soldering is not needed anymore. The USB connector will not provide 5V for the board, if you need to refresh the firmware, please provide external power supply. The power port has been changed from hollow to solid one to provide higher current-carrying capability. The three heater connecter has been changed into blue ones: 2-pin RC301 5.0mm 15A Package list: 1 x Geeetech GT2560 3D Printer Controller board About taxesDelivery detailsTerms of salesAbout usContact usAbout taxesTaxes and fees need to be paid by the buyer, and When the customs informs you;The specific cost of customs clearance is determined by the local national policy; If the buyer is required to pay VAT again when the item enters the customs, please provide the order bill to the customs; 1. To Europe, the vat tax rate is 19-22% 2. To the UK, the vat tax rate is 20% 3. To Australia, the vat tax rate is 20% 4. To Singapore: Under the DDU trade terms, the import tax for each ticket value exceeding USD 290/SGD 400 shall be charged at the actual tax rate, which shall be borne by the buyer; 5. To Malaysia: Under DDU trade terms. For packages exceeding USD120/MYR500, 5-10% tax shall be paid for the package, which shall be borne by the buyer; 6. To Brazil: Under DDU trade terms. 30-40% tax shall be paid for wrapping, which shall be borne by the buyer; 7. To Mexico: Under DDU trade terms, the total amount of parcels delivered by the seller to the same buyer on the same day does not exceed US$50; 8. To Israel: Under the DDU trade terms, the declared amount of a single parcel in Israel is less than US$75; 9. To New Zealand: Under DDU trade terms, the value of a single parcel does not exceed 400 New Zealand dollars (approximately 270 US dollars); if the total value of a single parcel exceeds 60 New Zealand dollars, the buyer shall bear; 10. To Canada: Under the DDU trade terms, the value of a single package exceeding 20 Canadian dollars will incur customs duties, which will be borne by the buyer;Delivery details 1. Items will be sent from China2. Items will be shipped within 5 business days after received a verified payment. Terms of sales1. Please confirm you are putting a correct and complete shipping address here.You are resposible for extra charge if your package been returned because of wrong address. 2. If there are any problems with our products,Please feel free to contact us. 3. If you are not satisfied with our products or services,please DO tell us.We will try to solve it well. 4. If you are satisfied with our service, tell your friends to buy it and leave us 5 stars positive feedbacks. About usShenzhen Getech Co .,Ltd( Geeetech) is an innovative, technology oriented enterprise that is specialized in the R&D, manufacturing and sales of 3D printer and the spare parts of 3D printer. Geeetech has been one of the most prominent rising star in the area of 3D printing in Shenzhen ,China, even the world, since founded in 2011. Geeetech advocates making 3D printing easy and economical and we are hoping to help more enthusiasts get easy access to the wonderful world of 3D printing.Contact us1.We are always here for you,offering friendly, comprehensive customer service every step of the way. We sincerely hope our item and customer service can give you the BEST BUYING EXPERIENCE on eBay. 2.We greatly appreciate your POSITIVE feedback. Please do NOT leave negative feedback without any contact. Working Day: Monday to Saturday. Working Time: 9:00 am to 18:00 pm (GTM +8:00 Beijing) If anything we could help you,please feel free to contact us.

Price: 31.19 USD

Location: shenzhen

End Time: 2024-02-05T08:50:19.000Z

Shipping Cost: 0 USD